I am off today, like most everyone else, so I don’t expect too manyĭo drop by today, well, here is your July 4th Spark! Guess what
#Ethernet status down pro
Spark! Pro series – 4th July 2022 Spiceworks Originals.LC/0/0/CPU0:Jun 18 09:33:35.084 UTC: ifmgr: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface GigabitEthernet0/0/1/8, changed state to Up LC/0/0/CPU0:Jun 18 09:33:35.084 UTC: ifmgr: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/0/1/8, changed state to Up LC/0/0/CPU0:Jun 18 09:33:25.431 UTC: ifmgr: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface GigabitEthernet0/0/1/8, changed state to Down LC/0/0/CPU0:Jun 18 09:33:25.430 UTC: ifmgr: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/0/1/8, changed state to Down LC/0/0/CPU0:Jun 18 09:33:25.172 UTC: ifmgr: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface GigabitEthernet0/0/1/8, changed state to Up LC/0/0/CPU0:Jun 18 09:33:25.171 UTC: ifmgr: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/0/1/8, changed state to Up LC/0/0/CPU0:Jun 18 09:33:04.523 UTC: ifmgr: %PKT_INFRA-LINEPROTO-5-UPDOWN : Line protocol on Interface GigabitEthernet0/0/1/8, changed state to Down Text LC/0/0/CPU0:Jun 18 09:33:04.523 UTC: ifmgr: %PKT_INFRA-LINK-3-UPDOWN : Interface GigabitEthernet0/0/1/8, changed state to Down What else can I try to resolve this issue? I've been trying to get this working for around 5 weeks (1 hour per week max) and the deadline to get the network up and running is coming very close now. Moved the cable to port Gi1/0/2 and applied the config to no avail, moved back to Gi1/0/1 Connected a laptop to port Gi1/0/1 and got green LED, so assume the port is functioning OK.
Copied config from fully working site B, updated VLANs and applied config to switch in site A to no avail. Switchport config is correct and set to trunk, although I don't think this will affect the down/down issue. CN router also shows the interface going up/down when disconnected and reconnected When one side is unplugged, both LEDs go green. Cable has been traced back and is definitely connected to correct port on CN router. Changed cable from straight to cross over and back
#Ethernet status down manual
Speed and duplex are auto, but working with the CN team we tried all combinations of auto and manual speed + duplex settings, with shut no shut inbetween each change There are no port security settings in the running config Site B also has the exact same setup and LAN equipment, just different VLANs to the CN PE router.īoth sites have 2 switches connected to the CN but for the purposes of troubleshooting I am focusing on one as a 'single' switch (no stacking).Īll switches are Cisco 9300s and routers are Cisco - not sure the model but are high end.Īs this switch is in a different site, getting someone to connect locally and provide access is troublesome and I can get around 1 hour per week if that. After lots of troubleshooting, I'm unable to get the port Gi1/0/1 up, it's always in the state down/down (notconnect).
#Ethernet status down how to
How to query or control network driver and hardware settings in Linuxįor wired Ethernet devices, you need to use a command called ethtool.I have a switch in site A that is connected to the core network PE router (managed by a different team) by a Cat6 cable. It also displayed my mac address 40:9f:38:28:f6:b5. The above command indicates that my Ethernet is up and running with 192.168.2.24/24 IP address.
0 kommentar(er)
